| Age | Commit message (Collapse) | Author |
|---|
|
Most modern games run on 60 fps, and for good reason. This gives
a much smoother experiences.
As some people have monitors that can do 144Hz or even 240Hz, allow
people to configure the refresh rate. Of course, the higher you
set the value, the more time the game spends on drawing pixels
instead of simulating the game, which has an effect on simulation
speed.
The simulation will still always run at 33.33 fps, and is not
influences by this setting.
|
|
Sleep for 1ms (which is always (a lot) more than 1ms) is just
randomly guessing and hoping you hit your deadline, give or take.
But given we can calculate when our next frame is happening, we
can just sleep for that exact amount. As these values are often
a bit larger, it is also more likely the OS can schedule us back
in close to our requested target. This means it is more likely we
hit our deadlines, which makes the FPS a lot more stable.
|
|
Before, every next frame was calculated from the current time.
If for some reason the current frame was drifting a bit, the
next would too, and the next more, etc etc. This meant we rarely
hit the targets we would like, like 33.33fps.
Instead, allow video-drivers to drift slightly, and schedule the
next frame based on the time the last should have happened. Only
if the drift gets too much, that deadlines are missed for longer
period of times, schedule the next frame based on the current
time.
This makes the FPS a lot smoother, as sleeps aren't as exact as
you might think.
|
|
During fast-forward, the game was drawing as fast as it could. This
means that the fast-forward was limited also by how fast we could
draw, something that people in general don't expect.
To give an extreme case, if you are fully zoomed out on a busy
map, fast-forward would be mostly limited because of the time it
takes to draw the screen.
By decoupling the draw-tick and game-tick, we can keep the pace
of the draw-tick the same while speeding up the game-tick. To use
the extreme case as example again, if you are fully zoomed out
now, the screen only redraws 33.33 times per second, fast-forwarding
or not. This means fast-forward is much more likely to go at the
same speed, no matter what you are looking at.
|
|
_realtime_tick was reset every time the diff was calculated. This
means if it would trigger, say, every N.9 milliseconds, it would
after two iterations already drift a millisecond. This adds up
pretty quick.
|
|
On all OSes we tested the std::chrono::steady_clock is of a high
enough resolution to do millisecond measurements, which is all we
need.
By accident, this fixes a Win32 driver bug, where we would never
hit our targets, as the resolution of the clock was too low to
do accurate millisecond measurements with (it was ~16ms resolution
instead).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
We assume a conforming C++11 compiler environment that has a valid <thread>-header.
Failure to run a real thread is handled gracefully.
|
|
This switch has been a pain for years. Often disabling broke
compilation, as no developer compiles OpenTTD without, neither do
any of our official binaries.
Additionaly, it has grown so hugely in our codebase, that it
clearly shows that the current solution was a poor one. 350+
instances of "#ifdef ENABLE_NETWORK" were in the code, of which
only ~30 in the networking code itself. The rest were all around
the code to do the right thing, from GUI to NewGRF.
A more proper solution would be to stub all the functions, and
make sure the rest of the code can simply assume network is
available. This was also partially done, and most variables were
correct if networking was disabled. Despite that, often the #ifdefs
were still used.
With the recent removal of DOS, there is also no platform anymore
which we support where networking isn't working out-of-the-box.
All in all, it is time to remove the ENABLE_NETWORK switch. No
replacement is planned, but if you feel we really need this option,
we welcome any Pull Request which implements this in a way that
doesn't crawl through the code like this diff shows we used to.
|
|
In 10 years there is no commit to change how BeOS works, and we
have no active maintainer for it. It is unlikely it works in its
current state (but not impossible).
With the arrival of SDL2 (and removal of SDL), BeOS is no longer
support. SDL2 suggests to use Haiku instead of BeOS.
|
|
macro _WIN32
|
|
|
|
|
|
|
|
SaveLoadOperation to avoid nameclash with windows compiler toolkit.
|
|
DetailedFileType.
|
|
on unspecified behaviour.
|
|
"unsafe" functions to prevent them from being used, and thus having to care about certain aspects of their return values
|
|
nothing to do and nobody paying attention
|
|
|
|
Eagle_rainbow)
|
|
instead of declaring it in 6 other files
|
|
GUI-less video driver.
|
|
|
|
|
|
load), and add support for (safe) loading with a LoadFilter
|
|
milliseconds per game tick and use it
|
|
to terminate a dedicated OpenTTD
|
|
|
|
missed :)
|
|
VARDEF and put them in a more logical location
|
|
sync during GUI operation.
|
|
|
|
if a header require a header make it include that header
|
|
with a dedicated server
|
|
allocated.
|
|
|
|
|
|
_local_company, but only as a storage location for the company you want to join in MP.
|
|
|
|
sources too
|
|
|
|
hardcode the values for that enum.
|
